How To Stop ADT Alarm From Beeping?

ADT Security Alarm System is one of the most popular home & business security systems today. It allows you to protect your home by setting and monitoring multiple alarms around your house. The ADT system is very easy to use, and in general, there are no problems with its maintenance. Although, some new users may encounter “problems” in the beginning until they get used to it. One of the most common problems is the constant beeping alarm that is coming from your ADT Alarm System. In this article, we’ll explain why this problem occurs and how to solve it.

How To Stop ADT Alarm From Beeping?

So How To Stop ADT Alarm From Beeping? To stop and silence your ADT Alarm System from beeping just press the [OFF] or [#] buttons that are located on the keypad. The reason why your ADT Alarm started to beep is the cause of a low or dead battery in the control panel. Recharge or replace the battery and wait for the power to be restored.

All alarm systems need electricity (power) to operate, and if your alarm isn’t getting any power, you will get the beeping signal that something is wrong. In most cases, this problem is solved by replacing the old battery and putting a new one. You can also check on Amazon other great security systems.

It would also be desirable to check if your ADT alarm system was alerting you just for that or there may be some other issue also that you need to check. Below we will explain how to proceed in this situation if this problem happens to you. So, let’s start.

How Do I Silence Or Stop ADT Alarm’s Beeping?  

You’re tired of that annoying beeping sound from your alarm system? We don’t blame you at all! Most alarm systems including the ADT security alarm system will start beeping as a result of a low battery, total power outage or a failure to recharge the system backup battery. Things like that can be very easily and quickly solved without any excessive knowledge. To silence your ADT alarm system just do the following:

• Press the [OFF] button on the keypad
• Press the [#] button on the keypad

Note: DO NOT press these two “*” or “#” keys simultaneously! This combination is used as an emergency signal, and it signals the police.

If the steps above don’t work, just refer to your alarm system user’s manual to see the specific instructions. To order a replacement battery for your system, you can use this Battery Identification Guide to see which model is required for your control panel. You can also check on ADT’s official website to see what to do if your alarm is beeping.

1. Recharge The Battery

Most security alarm systems just like ADT run on battery (or have a backup battery). The problem with such systems is that you need to regularly maintain the batteries so that they do not discharge. Depending on the type and quality of the battery, they should be changed at least once a year. When the battery has low power, the ADT system will start beeping to alert you that the batteries need to be replaced. Therefore, you will need to replace your old batteries.

Solution: Recharge The Battery

To do this, do the following steps:

1. Locate the ADT alarm control panel (it’s usually located in the utility room or basement)
2. On your ADT keypad, press the [OFF] or [#] button to silence the beeping
3. Open the control panel with a screwdriver.
4. Disconnect the battery from the ADT circuit board.
5. Charge the battery and return it to the circuit board
6. Check on your alarm keypad to see if the low battery notification is disappeared.
7. Power needs to be restored. This may not be an instant fix, the system needs to recharge, and it usually takes 48 hours for the panel to recognize battery change.

Note! If the warning persists, then you’ll contact a ADT security system professional.

2. Replace The Old Battery With New Battery

If you use your ADT Alarm System for a long time, it is possible that the battery on it has lost its life span and run out. Therefore, it’s time to change it with a new battery. To do this, follow these steps and you’ll be fine:

Solution: Replace old batteries with new batteries

To do this, do the following steps:

1. Locate the ADT alarm control panel (it’s usually located in the utility room or basement)
2. On your ADT keypad, press the [OFF] or [#] button to silence the beeping
3. Open the control panel with a screwdriver.
4. Disconnect the battery from the ADT circuit board.
5. Identify the battery type. Purchase the same type so it can match your control panel.
6. Reconnect a new battery to the circuit board.
7. Check on your alarm keypad to see if the low battery notification is disappeared.
8. Power needs to be restored. This may not be an instant fix, the system needs to recharge, and it usually takes 48 hours for the panel to recognize battery change.

Here we will give you a great YouTube video with a step-by-step guide that also explains how you can replace your old battery with the new one for your ADT Alarm System.

If you want more security in your home, you can learn how to install hidden cameras. Read this fantastic article How to Hide a Camera in Your Bedroom?

Conclusion

As we mentioned above in this article, ADT Security Alarm System runs on batteries, and every time your battery is low, it will notify you with a beeping sound. This is done so that you are warned to change the batteries on your device as soon as possible.

Just as on your remote control, mobile phones, laptops, and other devices, you want to make sure that the battery is fully charged, so you can pay attention to your safety system. Depending on the type of batteries you use, batteries are usually replaced at least once a year. I hope that this article has helped you and that you will definitely pay attention to the security of your home.

Related Asked Questions

Why Does My Old ADT Alarm Keep Beeping?

When you have a low or dead battery in your old ADT alarm system, the system will activate and start beeping to notify you that it needs new batteries.

Why Did My ADT Alarm Go Off For No Reason?

The ADT alarm system may go off for several reasons, such as the low battery, sensor issues, or improperly placed sensors.

Does ADT Replace Batteries?

ADT is providing several battery-replacement options for their users, where they also include a self-service option for their systems and devices. It comes with the easy step guide that will get you ready to replace a battery.